</>
|
|
SealBoss ® Product Line:
Concrete Repair Products
Crack Injection Systems
Waterproofing Products
Joint Filler Compounds
Cartridge Systems
Specialty Coatings
Equipment & Accessories
|
|
SealBoss ® provides commercial grade, professional quality
concrete repair and waterproofing products, equipment and
accessories for commercial and residential applications.
For more detailed product information please look at these links:
|
|
</>
Concrete Mender
SealBoss QuickFix 6060 - Strong/Rigid Grade
Professional
Latest Polyurethane Technology For 10 Minute Crack Repairs
Floor Crack Repair System
Industrial Grade Repairs
Repair Problem Floors Fast
and even at Very Low Temperatures.
For Garages, Patio, Warehouses
and other Structures.
12 cartridges total and mixers from the following products.
The Commercial Grade Do It Yourself Kit includes:
1 Handgun 1:1 mix-ratio
12 22oz 6060 Universal Polyurea Sealer (Thin - for cracks)
12 Static Mixers
1 Repair System Manual, Product Information
1 Pair Latex Protective Gloves
(picture shows 6500 and 6060 cartridges - this order only 6060 cartridges)
Toll Free Telephone Support, SealBoss Hotline 1877-932-2293
For more detailed product information please look at these links:
Do It Yourself and save BIG
Ultra Fast Repairs
Crack Repair, Spall Repair
Available in colors
Flexible and Rigid
Products also available in 5 gal units & drums
RANGE OF APPLICATION
Shallow spalls on bridge decks Traffic area spalls & crack repairsGrade matching Floor repairStops additional damage Fill & repair spall before coating Used to “knit” cracked slabs Filling voids under concrete and tile
100% Solids, Meets VOC Regulations
Return Project to Service in 60 Minutes
Cures From -20OF to 130OF
Odorless
Resistant to Petrochemicals
Industrial Facilities
Warehouse Floors
Manufacturing Facilities
Pulp and Paper Mills
Bottling and Canning Facilities
Water and Waste Water Treatment
Cold Storage Facilities
Freezers
TYPES OF MATERIAL
6060 QuickFix is an advanced polyurethane - polyurea formulated, rapid set, high strength, ultra low
viscosity repair material. The product is a two part, 1:1 mix ratio by volume, 100% solids system. This means it is
100% solvent free and VOC free. The material has been designed to fix spalled
concrete surfaces and cracks, and to rebuild damaged control joints effectively and quickly.
Examples for typical repair applications are warehouse floor spalls and other traffic prone surfaces,
where load damage from steel wheels, hard urethane wheels and other stress factors are common.
6060 QuickFix is also a strong adhesive to bond damaged slabs. The product adheres very well to itself
(wet on dry). Quickfix is not intended for use where movement is required. For moving control joints please refer to our flexible products such as SealBoss 6500 Polyurea.
6060 QuickFix is slightly moisture sensitive and should be applied on dry surfaces.6060 QuickFix offers the same physical properties at an extended 'open time' for large applications.
APPLICATION
Clean the area of debris and contaminants, such as oils, loose materials, dirt, rubber etc., for good adhesion
of the product. Expose clean rough concrete for best results. If using a saw to cut concrete and clean the crack,
remove all the dust from the cut out area. Make sure the area is dry. Vacuum or blow off cement dust.
Deep Crack / Joint Application
Apply product to the bottom of the crack and work up in layers.First apply product, then deliver sand
into the applied product. Then add more product & sand. Repeat the steps until reaching the finished grade.
FILLER
Sand filler should be free of moisture. Grit sizes from 12 to 60.. In exterior applications, the use of dry silica
sand will reduce discoloration from UV Rays. Pea gravel can be used on very large spalls.
GRINDING TO FINISH GRADE
Allow
6060 QuickFix to set for about 15 minutes or until hard. For best results use a flexible grinding
wheel. Scrapping or cutting may also be done with a sharp razor blade cutter. Cut as soon as product is set
and but not completely hard yet. Repair is now ready for traffic.
MAINTENANCE OF EQUIPMENT
Remove all excess sealant and any smears. Tools and mixing equipment are best cleaned
immediately after use. Solvents are hazardous, are aggressive towards plastic and rubber and might be in
conflict with regulations on the jobsite. Caution! Some cleaners are combustible.
SAFETY / PRECAUTION
Protect your health! While working with SealBoss materials, safety goggles, gloves and safety clothing
must be worn at all times. Consider property in proximity of the application area to
prevent loss or damage. Protect your jobsite from unauthorized persons. Store all materials and equipment
safely and out of reach of children! Observe container labels, MSDS, and
instructions in the SealBoss Product Catalog before using the product and equipment. In case one of the
components comes in contact with the skin, wash thoroughly with soap and water. Provide adequate
ventilation in volume and pattern in working area. Further protection: emergency showers and eyewash stations.
</>