| | |
| Search By Manufacturer
| |
| | |
|
- > DIY Repair Kits, For Foundations, Walls, Floors
- > Concrete Repair, Injection, Waterproofing Equipment
- > Concrete Repair, Injection, Waterproofing Products
- > Floor Joint Fillers, Joint Repair, Caulking, DIY Kits
|
| | |
| Subscribe To Mailing List
| |
| | |
|
|
* SealBoss COMBO KIT, 5 Gal 1510 +15X PU Injection Grout, 2 Gal R70 Flush,100 Injection Packers, 1 Drill Bit
|
Manufacturer: SealBoss Corp.
|
|
|
SealBoss ® Product Line:
Concrete Repair Products
Crack Injection Systems
Waterproofing Products
Joint Filler Compounds
Cartridge Systems
Specialty Coatings
Equipment & Accessories
|
|
SealBoss ® provides commercial grade, professional quality
concrete repair and waterproofing products, equipment and
accessories for commercial and residential applications.
For more detailed product information please look at these links:
|
|
1510 WATER - STOP INJECTION COMBO KIT
Included:
5 Gal SealBoss 1510 Poyurethane Injection Foam Grout
.5 Gal Accelerator
2 Gal SealBoss R70 Pump Flush
100 13-100AL 1/2" Mechanical Packers - Injection Ports
1 LongLife Drill Bit
SealBoss Combo Kits comes complete with resin, pump flush, packers, and drill bit.
This kit provides enough material and equipment to do about 150' of concrete crack repair.
Professional
Pressure Crack Repair &
Leak-Stopper - Water Stop System
Satisfied Customer Testimonial
|
Michael P.
SealBoss. customer
Craig,
Just wanted to say how glad I was to have your product on Monday. I live in Cobb County, GA and the water came pouring in during our recent flooding. I had already actually patched one of my two retaining wall cracks and already had the holes drilled for the second. However, I had not pumped the second one, so I got a desperate call from my wife for help when the rain hit that critical point and water stacks up against the front of our house. I got there from work as quickly as I could and still had to tighten the packers and mix the resin, but I had the water stopped inside of 15 minutes and we got nothing wet except for a few towels! What a lifesaver! There are a couple of areas that I just could not get the foam into so I am going to have to drill a few holes to make certain everything is sealed. I will need to order a few more more packers for that. I have bragged to many guys here at work about the DIY system and several have asked for your info for themselves or others, so I have passed your website along to quite a few already!
Thanks Again,
Michael
|
|
POLYURETHANE (PU)
|
CHARACTERISTICS:
|
EPOXY (EP)
|
|
- Flexible to semi-flexible sealants with little structural strength
- React to foams (water-stops), gels and solid (non cellular) flexible or semi flexible sealants.
- Classified as hydrophobic (foams/resins) for crack injection, joints voids or hydrophilic (foams/gels) for curtain, bladder injection behind structures. Both groups are water activated for use in wet environments - Superior water-stop capabilities
- Single or two component, accelerators common. Viscosities low to medium. Very resistant, long term solution.
SealBoss recommended Products:
Foams: 1510, 1570, 1572
Flexible resin: 1400 LV-Resin Line
Gel/Foam: Flexgel2
|
- Rigid, very strong adhesive for structural repairs in mainly dry environments, typically reduced adhesion on wet surfaces. Excellent to regain structural strength in torn structures: earthquake damage, extended stress damage
- Not a water-stop material and does not tolerate extended movement.
- Two component. Viscosities from very low to paste. Very resistant, long term solution.
SealBoss recommended Products:
Resin: 4040
Paste/Putty: 4000 Quickseal
Cartridge System: 4000 Epoxy Cartridge System
|
|
POLYURETHANE
|
APPLICATION TECHNIQUES:
|
EPOXY
|
|
- Mechanical packer injection at higher pressures 300-3000 psi
Reason: PU injection is often performed in a wet environment where adhesives for surface ports cannot be used. Mechanical packers are installed by drilling a hole into the structure which the packer fits snugly. The packer is tightened mechanically for high pressure injection. PU immediately reacts with moisture in the crack increasing resistance of product flow which explains the high injection pressures.
SealBoss recommended Products: Complete line of packers: S-Type, R-Type, custom sizes, Hammer-in packers, surface ports, specialty packers
|
Conclusion: PU generally needs higher pressures and therefor the more sophisticated connectors / packers. There are many exceptions. For example curtain injection with PU gel into the space between structure and soil needs lower injection pressures but higher rates of material flow. The filling of larger voids and joint injection also uses lower pressures. PU injection through surface ports is not common, but high pressure epoxy injection through packers is seen more frequently. Reasons could be very thick concrete to be penetrated or damp / wet surface conditions.
|
- Surface port injection at lower injection pressures 30-800psi
Reason: Injection is typically done in dry environments and surface ports can be attached easily with epoxy adhesive. Holes do not have to be drilled . However the crack surface between the ports has to be surface sealed to prevent leakage during injection. The viscosity of the epoxy resin stays low during the injection process, resulting in much lower injection pressures.
SealBoss recommended Products:
surface ports, specialty ports
|
|
POLYURETHANE
|
PUMPING TECHNIQUES / THE EQUIPMENT
|
EPOXY
|
|
- Single component equipment for most water-activated hydrophobic
PU foams, accelerator to be added prior to pumping.
- Either single or two component equipment for true two component
PU resins such as 1400 LV-Resin Line.
- Either single component or multi-ratio two component equipment
for hydrophilic PU Gels based on the application and product. In multi-ratio pumping one component carries a high water content.
Single component pumps include inexpensive hand held devices, hand pumps and electric pumps. Multi ratio devices can be manual, electric and pneumatic. Some PU injection pumps can be used for epoxy injection (with limitations). SealBoss supplies PU as small as 1 gal units. We do not supply PU in cartridges for the following reasons: 1. Reduced shelf life in cartridge due to high moisture sensitivity, 2. Limited Injection pressure. For small jobs we recommend our (3000psi) handgun and a 1 gallon unit.
SealBoss recommended Products:
Hand held guns, manual pump HP100, electric pumps IP395 Pro, P1001
|
Final Remarks: Injection Technology has become more refined and in cases more confusing. Modern products are very capable, but similar characteristics are not easily distinguished by the untrained person. To avoid costly failures caused by product/job mismatches, SealBoss provides thorough technical support to make your job a good one. Please make use of our services - we are just a phone call away.
|
- Two component equipment for most epoxy resins for ease of use and precise mixing.
- Single component equipment for small jobs and epoxy with longer gel-time. Observe gel time closely and clean equipment
thoroughly. Epoxy is a very strong adhesive and may render a pump unusable.
- Pneumatic or manual guns for cartridge systems / smaller jobs
Two component injection pumps are pneumatic or electric. SealBoss supplies EP resins and paste also in cartridges for the following reasons: 1. Ease of use, 2. Cost, 3. EP is not very moisture sensitive and injection pressures can be handled by quality cartridges and dispensers. Dispensers are manual or pneumatic. With very few exceptions EP pumps are not to be used for PU injection.
SealBoss recommended Products:
Hand held guns, pneumatic pump PA3000, 4000 Cartridge System
|
|
Product Reviews
|
| | |
| Shopping Cart
Your cart is empty.
| |
| | |
|
|
|